Model: WL-WN570HN2-GW
Easy installation, flexible placement.
Supports AP, Router, Repeater modes.
Robust weatherproof enclosure design, 15KV ESD and 6KV Lightning Protection.
Complies with IEEE 802.11 b/g/n standards, wireless speed up to 300Mbps.
2x7dBi high-gain antennas.
Supports WPA/WPA2 (TKIP/AES) Encryption modes.
Features 6 LED status indicators.
High-Speed Outdoor Wi-Fi Solution
Supports AP, Router, Repeater, and AP+Repeater modes for flexible networking. Easily adapt to different environments and extend Wi-Fi coverage with seamless connectivity.
Supports 2.4GHz frequency and single-channel transmission, suitable for indoor and outdoor wireless networking. Typical indoor coverage reaches up to 492 feet, with extended range achievable in open outdoor environments.
The outdoor access point features an IP67-rated waterproof housing that offers excellent protection against dust and water ingress. This rugged enclosure ensures reliable operation even in harsh outdoor environments or during temporary exposure to rain.
Whether deployed in yards, parks, or other outdoor public spaces, the 2 x 7dBi high-gain omnidirectional antennas significantly enhance both the range and stability of your wireless connection, delivering reliable Wi-Fi coverage over a wider area.
WPA2 encryption enhances Wi-Fi security by strengthening data protection, helping to keep your personal accounts and network systems safe — even in public areas.
SPECIFICATION
| Hardware | Wireless | ||
| Ports | 1 x WAN/LAN | Standard | IEEE 802.11b/g/n |
| Button | 1 x Reset | Frequency | 2.4GHz |
| LED | 1 x Power 1 x WAN/LAN 1 x WiFi 3 x Signal |
Transmit | 28dBm MAX |
| Sensitivity | 802.11b: -93dBm / 802.11g: -73dBm / 802.11n: -68dBm | ||
| Flash | 8MB | Speed | 11n: Up to 300Mbps(dynamic) 11g: Up to 54Mbps (dynamic), 11b: Up to 11Mbps |
| DDR2 | 64MB | ||
| Power Supply | Input:100 - 240 Va.c. 50/60Hz DC 54V/0.3A Power over Ethernet（Passive） |
Wireless Security | WPA-PSK/WPA2-PSK encryption |
| ated Voltage/ requen | Input:100 - 240 Va.c. 50/60Hz | Antennas | 2x7dBi Omni Directional Antennas |
| ated Voltage/ requen | Input:100 - 240 Va.c. 50/60Hz | Distance | Outdoors 500m, Indoor 150m(According to the actual |
| Dimensions | Software | ||
| Unit | 180mm x 50mm x 50mm (L x W x H) | WAN Type | PPPoE, Dynamic IP, Static IP,WISP, Repeater |
| Environmental | DHCP Settings | Server, Client | |
| Operating Temperature | -10 °C to 50 °C | Function | AC Controller (option) Time Setting DHCP Server Wireless Setting |
| Storage Temperature | -30 °C to 70 °C | ||
| Relative Humidity | 10% - 90%,noncondensing | ||
| Relative Humidity(Storage) | 10% - 90%,noncondensing | ||
1. Please connect the wifi signal of wavlink device then use http://waplogin.link or http://192.168.30.1 to log in the management page.
2. Try to use different device like your phone or pc to log in the management page.
3. If you try to use your phone to log in the management page,please try to disable the mobile network.
4. If you try to use your pc to log in the management page,please make sure your pc is not connect to the router via Ethernet cable.
5. If you can't log in the management when the device is in AP Mode, please check the IP address arranged by the upstream router, then use this IP address to log in.
No,they are not waterproof,please keep them away from the water.
When there is no obstacle between the wavlink device and the target area,the 5g signal could reach about 300m and the 2.4g signal could reach about 100m for clients like phone.
Please try to avoid the obstacle.
The actual distance may depend on the environment.
Please be free to contact our support team if you meet any problem.
Yes,it is necessary to install the ground wire to avoid Static electricity and lightning strikes.
If you configure the wavlink device as repeater mode.
1.Please make sure you should enter the correct wifi password of the host router when you try to repeat the wifi signal.
2.Please make sure the dhcp of the host router is enabled.
3.Make sure the mac filter of the host router is not enabled.(Otherwise the wavlink device might be blocked)
If you configure the wavlink device as AP mode.
1.Please make sure the dhcp of the host router is enabled.
2.Make sure the mac filter of the host router is not enabled.(Otherwise the wavlink device might be blocked)
3.Please connect the pc to the modem/host router via Ethernet cable directly and check if you could get internet.(To rule out the problem of the modem/router)
No,this device could only form mesh system with the specific wavlink device which support everything mesh technology.For the devices which support everything technology,please refer to the link below:
Yes,our device could support ap/router/repeater mode.
In repeater mode,it could build a wireless connection with the starlink router.
In router/ap mode,you could connect the wavlink device to the starlink router via Ethernet cable.
Please press the reset button for 6s when the device is powered on.
No the device could not repeat the signal with captive portal.
Yes,it could be powered by the solar battery,just make sure you could provide DC48-54v for the device.
In repeater mode,the wavlink device could build a wireless connection with the host router,you need not connect the wavlink device to host router via Ethernet cable.
However you still need to connect the wavlink device to the poe box via Ethernet cable.It could only be powered by poe adapter/switch.
If the POE switch could support 802.3 at/af protocol,our device should work well with it.
Please configure the wavlink device as ap mode and connect it to the host router via Ethernet cable.Then you could control all the clients which connect to the wavlink device in the management page of the host router.
Top
Get the Scoop First
Subscribe to our official website to receive exclusive first-hand news and stay up-to-date on our new product releases and promotions!
