AERIAL HD10
Model: WL-WN573HP3
Compared with the traditional 256-QAM (Wi-Fi 5 uses), Wi-Fi 6 uses 1024-QAM for much faster wireless connections. Wi-Fi 6 also upgrades Wi-Fi security protocol to WPA3improves your network security with up to WPA2/WPA3-PSK MIX.
WN573HP3 achieves a total networking speed of about 1775Mbps — 1201Mbps on the 5GHz band and 574Mbps on the 2.4GHz band, sufficing almost any data-heavy activities
Four directional built-in 12dBi antennas greatly strengthen signals and achieve 1000m stable directional wireless coverage.
WN573HP3 supports MU-MIMO & OFDMA technique to simultaneously communicate with multiple devices in a very effective way.
Compatible with designated Mesh Wi-Fi system for seamless roaming and whole-home co
WN573HP3 can be used as an outdoor router or a ceiling router to meet more usage scenarios, providing more possibility.
Supporting both 802.3af/at active PoE and passive PoE power supply, making installation effortless and flexible.
The durable, weatherproof IP67 enclosure protects WN573HP3 against harsh outdoor conditions
Setting up in minutes with the WavRouter App or Web UI, easily managing Wi-Fi settings and monitor data usage.
1 x 10/100/1000Mbps WAN/LAN PORT (POE)
Reset/Pair Button
2 x 12dBi 2.4GHz antennas
2 x 12dBi 5GHz antennas
Built-in Directional Antennas
1 x SYS
input:100-240 Va.c. 50/60Hz
DC 54V/0.3A Power over Ethernet (Passive, adapter included)
DC 48V Power over Ethernet (Active, adapter not included)
IEEE 802.11ax/ac/n/a 5 GHz
IEEE 802.11n/b/g 2.4 GHz
802.11k/v
5GHz and 2.4GHz
5GHz: 2401 Mbps
2.4GHz: 574 Mbps
WPA2-PSK
WPA3-PSK
WPA2-PSK/WPA3-PSK MIX
Coverage
4x12dBi Built-in Directional Antennas
Multiple antennas form a signal-boosting array to cover more directions and large areas
Beamforming
Concentrates wireless signal strength towards clients to expand WiFi range
High-Power FEM
Improves transmission power to strengthen signal
Dual-Band
Allocate devices to different bands for optimal performance
DFS Access an extra band to reduce congestion
2X2 Streams
Connect your devices to more bandwidth
AP; Repeater; Mesh Router; Mesh Extender Modes
PPPoE, Dynamic IP, static IP
Wireless Backhaul
Ethernet Backhaul
Address Reservation
DHCP Client List
Server
IPV6
1× 5 GHz Guest Network
Local Web Managemen
Webpage (Internet Explorer 11+, Firefox 12.0+, Chrome 20.0+, Safari 4.0+, or other JavaScript-enabled browser)
SPI Firewall
Access Control
IP & MAC Binding
DDoS Attack Prevention
Auto Firmware Upgradel2tp
OTA Firmware Upgrade
Further software upgrade for feature availability may be required
5GHz:
11n HT20_MCS0:-87dBm,11ac HT20_MCS7:-69dBm
11n HT40_MCS0:-84dBm,11ac HT20_MCS7:-66dBm
11ac VHT20_MCS0:-87dBm,11ac VHT20_MCS8:-59dBm
11ac VHT40_MCS0:-84dBm,11ac VHT40_MCS9:-59dBm
11ac VHT80_MCS0:-81dBm,11ac VHT80_MCS9:-56dBm
11ax HE20_MCS0:-95dBm,11ax HE20_MCS11:-63dBm
11ax HE40_MCS0:-93dBm,11ax HE40_MCS11:-59dBm
111ax HE80_MCS0:-90dBm,11ax HE80_MCS11:-57dBm
2.4G:
11n HT20_MCS0:-85dBm,11ac HT20_MCS7:-69dBm
11n HT40_MCS0:-84dBm,11ac HT40_MCS7:-66dBm
11ax HE20_MCS0:-95dBm,11ax HET20_MCS11:-63dBm
11ax HE40_MCS0:-92dBm,11ax HE20_MCS11:-58dBm
ABS Plastic
240.6x239.9x62.4 mm（Not including antenna）
Operation temperature: 0ºC~40ºC
Storage temperature: -10~70℃
Operation RH (relative humidity): 10%~90%,noncondensing
Storage RH: 10%~90%,noncondensing
1x WiFi 6 Outdoor AP
1x Holder
4 X Cable Ties
1 x Quick Start Guide
1 x Some Screws
1x 54V Power Adapter
1x PoE Converter
1x Ethernet Cable
1. Please connect the wifi signal of wavlink device then use http://waplogin.link or http://192.168.30.1 to log in the management page.
2. Try to use different device like your phone or pc to log in the management page.
3. If you try to use your phone to log in the management page,please try to disable the mobile network.
4. If you try to use your pc to log in the management page,please make sure your pc is not connect to the router via Ethernet cable.
No,they are not waterproof,please keep them away from the water.
When there is no obstacle between the wavlink device and the target area,the 5g signal could reach about 300m and the 2.4g signal could reach about 100m for clients like phone.
Please try to avoid the obstacle.
If you configure one device as ap mode and configure another device as repeater mode,the distance between two devices could reach about 3000m if there is no obstacle between them.
The actual distance may depend on the environment.
Please be free to contact our support team if you meet any problem.
Yes,it is necessary to install the ground wire to avoid Static electricity and lightning strikes.
If you configure the wavlink device as repeater mode.
1. Please make sure you should enter the correct wifi password of the host router when you try to repeat the wifi signal.
2. Please make sure the dhcp of the host router is enabled.
3. Make sure the mac filter of the host router is not enabled.(Otherwise the wavlink device might be blocked)
If you configure the wavlink device as ap mode.
1.Please make sure the dhcp of the host router is enabled.
2.Make sure the mac filter of the host router is not enabled.(Otherwise the wavlink device might be blocked)
3.Please connect the pc to the modem/host router via Ethernet cable directly and check if you could get internet.(To rule out the problem of the modem/router)
No,this device could only form mesh system with the specific wavlink device which support everything mesh technology.For the devices which support everything technology,please refer to the link below:
https://kb.wavlink.xyz/docs/EverythingMesh/v100/Model-and-How-to-Add
Yes,our device could support ap/router/repeater mode.
In repeater mode,it could build a wireless connection with the starlink router.
In router/ap mode,you could connect the wavlink device to the modem/host router via Ethernet cable.
Please press the reset button for 6s when the device is powered on.
No the device could not repeat the signal with captive portal.
Yes,it could be powered by the solar battery,just make sure you could provide DC48-54v for the device.
In repeater mode,the wavlink device could build a wireless connection with the host router,you need not connect the wavlink device to host router via Ethernet cable.
However you still need to connect the wavlink device to the poe box via Ethernet cable.It could only be powered by poe adapter/switch.
If the poe switch could support 802.3 at/af protocol,our device should work well with it.
Please configure the wavlink device as ap mode and connect it to the host router via Ethernet cable.Then you could control all the clients which connect to the wavlink device in the management page of the host router.
Get the Scoop First
Subscribe to our official website to receive exclusive first-hand news and stay up-to-date on our new product releases and promotions!
